3500W-5500W 12-24V 6Blades Wind Turbine Generator + Charger + Slip Ring

Description

Wind Turbine Generator
for Land or
Marine Use
3500W 12V or 24V AC Wind Turbine
+
Charger
+
225A Slip Ring
Turbine Specification:
Body Material
Aluminium
Length
24.8 inches (63cm)
Number of Blades
6
Blade length
23.5 inches (60cm)
Starting Wind Speed
3m/s (7 mph)
Rated Wind Speed
12.5m/s
Survival Wind Speed
45m/s
Rated Power
3000W
Maximum Power
3500W
Weight
18.3lb (8.3kg)
This model includes:
-1 Wind Turbine
- Blades
- Slip Ring (installed)
- Hub
- Nose Cone
- Screws and Nuts
- Allen Key
- Instruction Manual
4500W 12V or 24V AC Wind Turbine
+
Charger
+
225A Slip Ring
Turbine Specification:
Body Material
Aluminium
Length
32.3 inches (82cm)
Number of Blades
6
Blade length
29 inches (73cm)
Starting Wind Speed
3m/s (7 mph)
Rated Wind Speed
12.5m/s
Survival Wind Speed
45m/s
Rated Power
4000W
Maximum Power
4500W
Weight
19.4 lb (8.8kg)
This model includes:
-1 Wind Turbine
- Blades
- Slip Ring (installed)
- Hub
- Nose Cone
- Screws and Nuts
- Allen Key
- Instruction Manual
5500W 12V or 24V AC Wind Turbine
+
Charger
+
225A Slip Ring
Turbine Specification:
Body Material
Aluminium
Length
32.3 inches (82cm)
Number of Blades
6
Blade length
29 inches (73cm)
Starting Wind Speed
3m/s (7 mph)
Rated Wind Speed
12.5m/s
Survival Wind Speed
45m/s
Rated Power
5000W
Maximum Power
5500W
Weight
20.5 lb (9.3kg)
This model includes:
-1 Wind Turbine
- Blades
- Slip Ring (installed)
- Hub
- Nose Cone
- Screws and Nuts
- Allen Key
- Instruction Manual
Introduction:
This is the most mechanically advanced generator in the market today. It features many upgrades that solves performance issues that our competitors struggle with. It is designed to work with charge controllers and grid tie inverters to better utilize the renewable energy generated. The following list will summarize its major features:
Connection Overview:
The Wind Generator is connected to the charge controller, which changes the Alternative Current output by the generator to Direct Current (AC to DC). Electricity generated by the wind turbine are then stored to batteries. Note: the 12V Batteries above are not included.
If your home or farm is connected to the power grid, on windier days you may be able to sell excess power generated by your wind turbine to your utility. At other times when the turbine cannot generate all the power you need, you would buy power from the grid. This concept is called net metering.
Even if net metering is unavailable, you might be able to reduce your power bills by using the electricity generated by wind turbines, and become less dependent on your utility.
Since wind speed increases with height, increases to the tower height can mean enormous increases in the amount of electricity generated by a wind turbine.
Blade Features
23.5 inch = 60cm , 29 inch = 73cm
- Color: White
- Length: 23.5" OR 29", depending on model (see spec for individual turbine)
- Incorporates highly efficient, true airfoil
- Quiet performance with minimal vibration
- Manufactured using a precision injection molding process that produces blades of exceptional consistency
- Made with new thermoplastic to increase durability
- Smoother and more durable than any blades you can find in the market
- High resistance to bending (over 150 degrees)
What is Nylon 6.6?
Nylon is extremely versatile in its applications. It is highly resistant to
abrasion
and has excellent
resilience
.
Within nylon, there are two groups:
nylon 6
and
nylon 6.6
. Nylon 6.6 is the
premium thermoplastic
. It is the thermoplastic that is most often specified by professional architects and designers because it provides the
flexural strength,
low-temperature toughness, UV Resistance
and is the most
resilient
. Nylon 6.6 performs well in many applications such as wind turbine blades, automotive parts, and other fields that get a lot of wear and tear. Nylon 6.6 has additional molecules that give extra strength and the resilience compared to nylon 6. If you still have no idea what Nylon 6.6 is, do a search on google.
Specification
Material
Nylon 6.6 + Carbon Fiber (<20%)
Mounting
6mm bolts
Length
23.5 inches
29.0 inches
Width (base)
5 inches
6 inches
Weight (per blade)
210g, 7.4oz
300, 10.6oz
Built-in Slip Ring
For those who are serious about wind power generation, this is a must have upgrade. Never again will the cable get twisted up. Never again will you have to climb up the ladder and fix the tangles.
With Slip Ring
No more tangles!
Without Slip Ring
Do you really want to untangle this every month?
Slip Ring Specification:
Circuits
3
Voltage
380VAC/DC
Maximum Current
75A X3
Rated Current
50A X3
Working Speed
250RPM
Temperature
-40'C to 100'C
Wire Gauge
6AWG
Number of bearings
2
Thread
M22x1.5
22mm diameter
1.5mm Thread Pitch
Features:
- High voltage / current carrying capacity
- Copper-graphite brushes ensure long life even under extreme load conditions
- Quick connector for fast connection to the AC / DC wind turbine *see reference picture below*
- Insulated with fiberglass sleeves to protect wires to the wind turbine and make the installation professional and tidy
- Easily taken apart for quick maintenance
- 2x High Quality Metal Sealed Ball bearing to stabilize axle
Built-in Tower Adapter with Anti Vibration & Fictionless Rotation System
With Dual Bearing
-
Dual Metal ball bearing
to prevent vertical vibration
- Yaw shaft diameter: 40mm
- 3cm of stabilizing distance with 2 bearings
- No vibration = Increase in efficiency
- Reduction in noise output
- One piece design Yaw body provides more stability
Without Tower Adapter / Bearing
- When there is no tower adapter, it makes installation harder than it has to be
-Without bearing, metal connection / joints will grind on each other and wear out
- Plays will get larger and turbine will vibrate during operation
Rotor & Body
short 24.8 inches (63cm), Long 32.3 inches (82cm)
- Bigger body allow fitting of a more powerful alternators
- Longer body and tail allow the turbine to face wind even if more blades are added
- High surface area tail will let the turbine stay focus to incoming wind
Specification
Body Material
Aluminum (with coating)
Length
See Model
Tail Height
33 cm
Tail surface Area
225 cm^2
Number of Magnets
12
Magnet Material
Rare Earth Neodymium magnets
Recommended Tower (Pipe) Size
1.5 inch schedule 40 pipe
Actual Pipe diameter: 48mm (1.9 inch)
Recommend adding 2.5mm padding
Yaw Body / Tower Mount
Inner Diameter
53.3mm, 2.1 inch
Hub & Nose Cone
Specification
Hub Material
Aluminum (with coating)
Diameter
140 mm
Capacity
6 Blades
Disc Thickness
23mm
Shaft Diameter
for 17mm shaft
Nose Cone Material
Plastic
Diameter
140 mm
Capacity
3 - 6 Blades (Depending on Model)
Height
93mm
Thickness
3mm
12V or 24V
Wind Turbine Charge Controller
Features:
System Voltage: 12V or 24V Nominal
Microprocessor based control electronics to control charging, outputs and dump load
Intuitive LED Display to reflect system status
Keeps battery in an optimum charged state
High quality finned aluminum casing to protect the interior and dissipate heat
Warning: Controller will get
damaged
if polarity of battery is incorrect, Dump Load must be connected at all times
Protection Features:
Dump Load MUST be connected at all time to protect the charge controller, no dump load = no warranty
Requires a minimum of 1.2Ohm 600W
resistive load
to be connected to the dump load terminal
Dump load activates when AC Turbine is >= 35V
Activating dump load will slow down the AC turbine and reduce voltage spikes.
Over voltage protection: All outputs will be cut when input voltage is over 30V. However dump load will stay on.
The
DUMMY
LED will turn
Red
when the dump load has been activated
Mechanical Specifications:
Operating temperature range
-25'C - 80'C
Weight
610g
1.35lb
Dimension (L x W x H)
15.1 x 13.1 x 6.9 cm
6.0 " x 5.2" x 2.7"
Mounting
Wall Mount at base
Cooling
Passive
Casing
High quality finned aluminum to act as heat sink for fast heat dissipation
Maximum Amperage on Terminals
DUMP LOAD: 28A
LOAD: 10A
BATTERY: 15A
Three circuit Max 75A X3 =225A Slip Ring for
12V, 24V, 48V up to 380V AC / DC
Wind Turbine Generators
Slip ring is a must have item if you do not want the cables toget twisted up.
Installation:
Install to the wind turbine's axis of rotation and you are done.
Accessories Pack:
For Air-X 403, 303, Ametek
-3 Degree Adjusters
- Six M6x25 Stainless Steel bolts
- Six hex Nylocks nuts (auto locks thread)
- in case the original set is misplaced
Degree Adjusters to fine tune blade angle
Increase/decrease blade angle by installing degree adjuster under the blades
"+" on the right side = Increase angle =
More
Torque, Less Speed
"-" on the right side = Decrease angle = Less Torque,
More
Speed
WARNING !!!
Rotating blades present the most serious mechanical hazard. The blades may be moving at velocities over 275 miles per hour (440 km/hr). At this speed, the tip of a blade is nearly invisible and can cause serious injury. Under no circumstances should you install the turbine where a
person could come in contact with moving rotor blades.
The installer of these blades is solely responsible for the use or misuse of these blades. We assume no liability for ANY injuries caused by these products
NO OPERATING COST
GENERATES ELECTRICITY FROM THE ABUNDANT RESOURCE - SOLAR & WIND
Terms & Conditions
Bidding this auction means that you agree with the following terms & conditions.
All pictures and descriptions are subjected to change without notice. Items may not look exactly the same as the auction shown. We are not responsible for any inadvertent errors.
Payment
Total payment = winning price + shipping & handling
Insufficient payment will be charge extra US{{detail_product_description}}.50 to compensate the Paypal penalty fees.
Shipping
&
Handling
Extended Area Surcharg
e:
For Address that our couriers determined to be outside of their normal service area, they will charge an additional "extended area surcharge". Minimum is
US.99
, we will notify you if it is higher.
Total shipping = Base S&H + Combine S&H ( for each additional item )
a) Charge the highest shipping cost for the first item.
b) No combine shipping.
** Please email us if you have questions with the S&H
1. Combine shipments are only available on the condition of a
SINGLE PAYMENT
. Auctions that are paid separately will NOT be shipped in combo and therefore, they are not qualified for shipping discounts.
2. We ship within 48 hours after payment is received and confirmed. Please allow up to
5-10 BUSINESS DAYS
for item(s) with a physical address sending to the 48 states of United States & Canada. For international bidders, the shipping time varies with respect to your location.
3. Bounce backs due to incorrect shipping address will result in setback on deliveries. It is the buyer's responsibility to repay the shipping & handling fees.
4. We are not responsible for any loses or damages resulting from shipping.
Return & Refund Policy
No refunds after 30 days
Shipping & handling & other service fees are
NOT
refundable
All returned items must be in original packing.
Items that are used/ damaged/ deformed or altered in any ways will not be accepted.
A 20% restocking fee will be charged on all refunded items.
E-mails
E-mails are usually answered within 2~3 business days in priority order.
Spams and mass e-mailing will be deleted without slightest glance.
E-mails with virus or anything subjected to hacking are automatically deleted.